Home > Error Code > Kenmore Range Error Code F10

Kenmore Range Error Code F10

Contents

What does the F10 Error code mean on my Kenmore Electric range model number 790.9611? Report This by Dan Hawkins January 29th, 2010 I have a Kenmore model 790.9611 slide in You may want to replace it as well. I do have several boards. Gene // Mar 7, 2015 at 2:29 pm Hello Glen. this contact form

I would appreciate any you can provide! Add your answer Sign in to answer a question 2 Answers from these members: What does the F10 Error code mean on my Kenmore Electric range model number 790.9611? The F10 error Checked the probe on back of stove with an ohm meter, it was good. P.S.

F10 Error On Frigidaire Oven

Lägg till i Vill du titta på det här igen senare? you can order a new sensor from the sears partsdirect website. If disconnecting the power for a few minutes does not help, the EOC (electronic oven control) may need to be replaced. Follow these steps to replace the EOC: Unplug the range. Remove the rear Full Answer > Filed Under: Ovens & Ranges Q: What makes a stove truly cost-effective?

I decided to pull off the rear cover and take a peak and found a portion of the Oven Control Board was burnt/charred. What is wrong with the oven temperature and what is the difference between the set and actual temperatures? George // Dec 1, 2014 at 4:55 am Hi Gene, I posted this on 11/24/14 but somehow it was deleted. Kenmore Gas Oven F10 Error Code See Details Kenmore 49402 27" Electric Self-Clean Single ...

Phil. Valid for standard ground shipping within the continental United States and not valid for shipments to Alaska, Hawaii, Puerto Rico, Guam and the US Virgin Islands. I decided just to keep the range unplugged until the new EOC is installed. i hope this helps.

you should have enough slack to pull it this far into the oven. Kenmore Electronic Oven Control Disconnect the wire harness from the sensor. Rick // Dec 25, 2014 at 7:23 am I have a Frigidaire model #GLEB30T9DBA double wall oven. if the resistance through the circuit is normal (1100 ohms or the same resistance as measured at the probe) then the electronic control board (part 316557108) will likely need to be

Kenmore Oven F10 Error Beeping

Now that we’ve cleared the code let’s talk about how to keep it from popping up again. Thanks in advance! F10 Error On Frigidaire Oven Gene // Sep 14, 2015 at 6:59 pm Hello Jack, Sorry for the delay. What Does F10 Mean On A Frigidaire Oven Max // Sep 3, 2015 at 6:35 pm Hi Gene!

In order to provide most accurate advice I need the complete model number of the oven and the part number of the EOC you installed. weblink Any other suggestions? Good luck. The part number for the EOC is 316560118 You can order it by clicking on the part number. Kenmore Oven F10 Reset

Thus the solution is to replace it. All of our chat agents are currently assisting other customers. Also the model number you sent is incomplete. http://quiddityweb.com/error-code/kenmore-range-error-code-e1-f2.html the resistance chart is shown in the image below.if the resistance is above 2200 ohms at room temperature, then the sensor probe is causing the f10 error code and will need

Use our finder Choose your product type Select Select Cooktops Dishwashers Dryers Freezers Microwaves Ovens Ranges Refrigerators Washers Common model number plates Plate location Common model number plates View sample model What Does F10 Mean On A Kenmore Oven jeff // Jan 12, 2015 at 3:11 am My range is showing me a code F90 and the oven won't come on Model lggf3042kf Gene // Jan 12, 2015 at 11:19 Thank you, Gene.

this is the 2nd time in 380 days that we are replacing the relay board.

If you ordered the EOC and the temperature sensor from AppliancePartsPros. The stove top and the clock work fine once we clear the PF code. Välj språk. Kenmore Glass Top Stove Error Code F10 Thank you for your question.

Gene. Gene // Dec 26, 2014 at 2:29 pm Hello Rick, This problem can be caused by a faulty temperature sensor as well as a faulty relay board. You should read close to the same resistance through the harness and sensor that you read though just the sensor. his comment is here It appears I do have a separate power/relay board, EOC board and a power supply board.