Home > Kenmore Elite > Kenmore Elite He4 Washer Error Codes

Kenmore Elite He4 Washer Error Codes


It is ONLY 9 months old. I do not recommend using the technical troubleshooting information in the chart unless you are completely confident in your technical ability to safely access internal washer components. Thanks for the helpful insight! 11/28/2015 by Anthony Rogers Used a T-20 torx bit to remove the two bottom access plate screws. Yes No Voted Undo Score 5 Cancel Comments: Amazing. this contact form

I found several of them on my computer board as well. The other three black relays are Omron G2RL-1AE. It may take a few visits to resolve the problem. Was this answer helpful?

Kenmore Elite He4t F11 Error Code

But this time it just wasn't working anymore. ft. Thank Again.

Please give me all the information and opinions you possibly have. Like Bookmark September 4, 2005 at 12:27PM Thank you for reporting this comment. Stay with me here! Kenmore Elite He3 Washer Error Codes Reminds me of one of the first computers,,, was it UNIVAC or ENIAC?

If you are interested in joining the class - I'll be posting the outcome of that conversation here. Kenmore Elite He4t Washer Error Code F02 Bottom line, the coin trap isn't a very good guard filter for the pump. Whoo Hoooo. Was this answer helpful?

Like Bookmark March 10, 2006 at 9:21AM Thank you for reporting this comment. Kenmore Elite He4t Error Code Dl F from what I've read, it's the CCU that is messed up, which I believe is located on the top in the rear. Cancel Dylan Rep: 97 1 1 Posted: 04/16/2012 Options Permalink History I too had this issue and thanks to Mayer and Chris Campbells post went straight to the problem. Cancel jhagner Rep: 25 1 Posted: 05/26/2014 Options Permalink History The F11 code is caused by either a CCU failure or an MCU failure...here's how to tell: If your machine starts

Kenmore Elite He4t Washer Error Code F02

Like Bookmark October 25, 2005 at 6:58PM Thank you for reporting this comment. We replaced the cpu board and its been working for about 3 weeks now, New board can be found on net for about $150.00. Kenmore Elite He4t F11 Error Code I swapped the MCU out last night, I replaced the CCU cover and snapped the CCU back in place, checked all the connections to make sure they were all seated in Kenmore Elite He4t Washer Fh Error Code In deed!

I hope you have better luck than I had. weblink So I popped their covers off - if anyone wants to fiddle with this, they are the two little white boxes on the board just right and down from center. Was this answer helpful? The tech said we'd have to pay for a second person's labor for someone else to come with him to help move the dryer out of the way. Kenmore Elite He4t Washer Manual

Back together and again, not it. It comes wrapped in special pink bubble wrap with a static precaution warning on it. Does anyone have any ideas on what to check next? navigate here Undo kent0 I too have this problem with an HE3T purchased in 8/04.

Heat up the contact point for each harness connection on the TOP AND BOTTOM OF BOARD and add a thin layer of solder. Kenmore He4t Washer Using the ratchet and the 7mm socket simple unscrew them and then slide the top cover backwards and then up and off.Step 3Label all of the connectors to the white box I tried to get technical advice when I was in the states, but noone seems to know what to do.

Yesterday I opened the top of the washer (only 3 screws at the rear of the top) and carefully removed the big white box that contains the suspect control board.

Works like new again. 0$. Check again closely -- usually the HEx machines will first flash the "F" then display another code --- either numbers or letters like H or DL) -- to help decipher the Clean the drain filter, check all hoses for blockage. Kenmore Elite He4t Washer Error Code F06 I removed the board from the plastic case and lightly polished all of the board contacts (both sides) with steel wool.

I did the fix with the relays but i seemed to have hosed the board somehow in the process. It is the down time that aggravates our family the most. The middle connector on the MCU looked different and I had to use my imagination to see a hairline crack even under my microscope (magnified such that an Exacto blade tip http://quiddityweb.com/kenmore-elite/kenmore-elite-washer-error-codes-f02.html Nope.

We have the one year try it for free plan. From what the tech said, the part is a few hundred dollars at least. I also re-heated and added solder to the contact points of the 5 relays. I think this reduced the chance of any short circuit between the contacts due to my beginner soldering skills.

F11...no its a loose connection! i really hope this information helps you today. Thanks everyone! 12/20/2015 by Christian Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? ft.

Ask a question Get up to 45 % off On Washers Related Questions Related Questions'>Why do I keep getting the F-21 error code on my Kenmore HE2+ front load washer model Put it back together and that wasn't it. Was this answer helpful? Preview my answer Post my answer View Statistics: Past 24 Hours: 72 Past 7 Days: 603 Past 30 Days: 2,817 All Time: 139,786 22,240 Free Manuals 87,221 Solutions 6,544 Devices iFixit

One of the tines is missing. I have been noticing that the wash cycle was taking an incredible amount of time to complete recently. This should clear the unit of the excess detergent. • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain I have not had this problem, so can't offer advice from personal experience, but here's what the tech sheet says: "If during the water heating step in the wash cycle, the

Cancel The All-New Pro Tech Toolkit The high performance electronics repair kit. To do so put the washer into its test cycle by selecting any wash setting, select DRAIN and SPIN, then select NO SPIN. I complained and they offered $100 reimbursement towards the part but I had to order if from Sears which costs more than some of the online shops but at least I Mine is black and goes from the back of the strainer right up to the underside of the tub.

I'd set up a service call at one point. I will dig deeper and report back soon. Thanks for the input, I'll report back on what works.