Home > Kenmore Elite > Kenmore Elite Washer Error Code F2

Kenmore Elite Washer Error Code F2

A little elbow grease and I was able to break the trap free. We of course stopped using the sheets and notified Dial (the main co.) After that first time the machine has run perfectly until this week. After the machine is reset and the drain/spin cycle is chosen (with clothes in the machine) it fails. She attended Tarrant County College and studied English composition. this contact form

It is displaying the error code F02. The F02 code was for filter in the pump just open the pump by turning the knob and watch out, if you have water in your washer it will drain out. Compact Electric ... Cleaning the filter every two or three months can avoid the clogs that are causing the F2 error code to appear on your Kenmore washer’s control panel.

Yes No Voted Undo Score 10 Cancel Comments: This list worked for me... Posted on Nov 10, 2008 Helpful 6 Not Helpful 1 Comment Flag Louie Role Nov 14, 2008 Hi again,Any development so far? Most common cause is something (or lots of things) stuck in the drain pump. usually the problem5.

Reach up along the inside of the front panel and locate the bottom of the door latch assembly.4. Yes No Cancel Update (+2 points) 10 more comments tappej Dec 28, 2008 hello,i am so excited that i could possibly fix my own washer b/c this is exactly the problem Mayor: An expert whose answer got voted for 2 times. Was this answer helpful?

Thank You oldturkey03. Advertisement Page 1 of 2 1 2 > Topic Options #569935 - 10/04/09 10:52 AM Kenmore Elite HE3t washing machine F02/SUDs error Mark_from_PA first timer Registered: 10/04/09 Posts: 1 Our Kenmore Was this answer helpful? Tip: use vice grips to hold the clamps open to replace the hoses.

It was jammed full. I checked my drain filter and it had paper and a baby sock in it. Spent the $162 for pump and motor assembly and works like a champ. Jim Dandy 59.745 weergaven 7:35 Washer Won't Drain? – Duet/HE3 Front-Load Washer Drain Pump Replacement (part #280187) - Duur: 2:21.

First, unplug the washer and access the main control board. I've had the same electrical issue with the "F" variable coming up for EACH cycle. There is a nice place that sells refurbished GUARANTEED boards for about $85 out there (New, these buggers run a good $225 or so). I have already replaced every part in my 8 year old washer and dryer except for the electronics.

Got the water out of the trap and took out the one screw for the pump but left the hoses attached. weblink Why am I getting an FL error code on a Kenmore Calypso washing Machine? ft. However, apparently is causing more suds than needed.

What was amazing was the stuff I found in there. To be fair to Kenmore, this unit has been in routine use for more than nine years, and this is the first problem. 01/28/2012 by Martin you are welcome :-) 01/31/2012 You probably won't be able to do it with simple pliers because you won't be able to get enough hands inside to make the hose changes. http://quiddityweb.com/kenmore-elite/kenmore-elite-washer-error-code-f17.html Got it in 3 days.

He said once a month run the machine on the hottest water cycle with a cup of bleach (no clothes). When they did my repairs they even replaced the stainless steel tub that was not broken. Took about an hour to resolve due to the small space and wet rug...

After the suds dissipate, you can normally run a rinse/drain and spin cycle.

Just started another spin cycle and it was ok. Sluiten Meer informatie View this message in English Je gebruikt YouTube in het Nederlands. Replacement worked great. Replaced pump and motor and still getting error codes.

Good Luck and I hope this helps. Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? But don't worry: you already unplugged the power cord, right?) Unscrew the trap cover a little (Don't remove it completely!) and let the water out. his comment is here I used a plug bar to switch it on, after I made the risky connection.

What do I do now?? Nasty. Sergeant: An expert that has over 500 points. Since I did it, it has ran perfectly for almost a year.

The hex screws caused me a bit of a quandry until I figured out I had an adaptor and used it.