Home > Kenmore Oven > Kenmore Elite Stove Error Codes F10

Kenmore Elite Stove Error Codes F10

Contents

The ice 10/19/2016 10/19/2016 JACUSTOMER-b2yaxe65- Bosch Maxx Classic Wont spin and will only allow first lot 10/19/2016 10/19/2016 JACUSTOMER-x0uwnnmp- LED lighflashing in freezer and fridge, whirpool 10/19/2016 10/19/2016 smitty1486, JACUSTOMER-b2yaxe65- WHICH If the meter shows a resistance of less than 1000 ohms or more than 1300 ohms at room temperature, the sensor will have to be replaced. I have also been getting an intermittent F10 error message on my Kenmore stove built in 2007. If the sensor is not reading correctly make sure you have hooked up the meter to the sensor the right way. navigate here

What does the F10 error code indicate? Share it! RepairClinic.com 93.876 προβολές 3:44 Range/Stove/Oven Repair - Replacing the Oven Temperature Sensor (Frigidaire Part # 316217002) - Διάρκεια: 5:25. Matt DeRoller 46.490 προβολές 7:39 How to unlock Kenmore oven - Διάρκεια: 1:07. If disconnecting the power for a few minutes does not help, the EOC (electronic oven control) may need to be replaced. Follow these steps to replace the EOC: Unplug the range. Remove the rear

F10 Error On Frigidaire Oven

The next step would be to reconnect the probe and then remove the upper back panel to access the electronic oven control board. if you have a volt/ohm meter, you can shut off the breaker for the range and remove the screws that mount this sensor to the back wall of the oven. frank espo, November 26, 2010 my oven mod # is 790.9612340a. See Details More Products Kenmore 49513 30" Electric Self-Clean Single ...

Ask Your Own Appliance Question Share this conversation Related Appliance Questions Question Date Submitted Have a may tag double oven stove. Learn More guaranteed fit All parts are manufacturer-approved, to ensure proper fit and to keep appliances running for years to come. Multimeterhttp://www.searspartsdirect.com/part-...Temperature Sensorhttp://www.searspartsdirect.com/part-...Electronic Control Boardhttp://www.searspartsdirect.com/part-...Find parts for your range at:http://www.searspartsdirect.com/parts...Or click here to schedule an appointment with a repair technician. Kenmore Gas Oven F10 Error Code you should have enough slack to pull it this far into the oven.

F., the broiler comes on (top of oven) instead of the bottom element. Kenmore Oven F10 Error Beeping All of our chat agents are currently assisting other customers. Thanks for watching. Found a site where guy said check all the purple wires since the wiring is colored coded.

Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & Kenmore Electronic Oven Control Disconnect the power to the oven. RepairClinic.com 44.104 προβολές 3:31 Kenmore Oven Error Codes - Διάρκεια: 2:58. The probe would need to be replaced.

Kenmore Oven F10 Error Beeping

The last two time I used the oven to heat something up the food was burned on top and raw on the bottom and there was an F10 code displayed. if you do not see the mounting screws on the back wall inside the oven cavity then you will need to remove the lower back panel of the oven (with the F10 Error On Frigidaire Oven Save model in your profile permanently Don't have a profile? What Does F10 Mean On A Frigidaire Oven Use our finder Choose your product type Select Select Cooktops Dishwashers Dryers Freezers Microwaves Ovens Ranges Refrigerators Washers Common model number plates Plate location Common model number plates View sample model

RepairClinic.com 113.500 προβολές 2:00 Why is My Oven Beeping and Saying F1? - Διάρκεια: 2:35. http://quiddityweb.com/kenmore-oven/kenmore-oven-error-codes-f2.html Full Answer > Filed Under: Ovens & Ranges You May Also Like Q: Is an induction cooktop the same as a glass cooktop? Share it! OK, Continue Tips for finding your unique model number Look for your model sticker, tag or plate. Kenmore Oven F10 Reset

If the reading is above 2,500 ohms, the sensor is broken and should be replaced. the part number for the sensor is 316217001.if the sensor resistance is normal, you can plug the sensor back in and measure the resistance through the circuit that plugs into the f10 error code and door is locked. his comment is here The broiler element was red hot.

Whats the model# of your range? What Does F10 Mean On A Kenmore Oven Forum Forum Home New Posts FAQ Calendar Community Albums Member List Forum Actions Mark Forums Read Quick Links Today's Posts Appliance PartsAppliance Maintenance TipsApplianceBlog Home Advanced Search Forum Appliance Repair Talk remove the upper back panel (with the range still unplugged) to access the control board.

Offer valid for online purchases only.

Kenmore Elite Electric range Model #79046719603 was saved to your profile. Kenmore and Craftsman model numbers typically have three digits separated by a period. the part number for the sensor is 316217002.if the resistance is normal, then one of the other causes mentioned above is producing your f10 code. F10 Kenmore Oven Some models have the probe secured with screws on the back panel of the oven.

Sears Holdings reserves the right to terminate or modify this offer at any time for failure to comply with its terms and/or due to any operational malfunction of the software, hardware the resistance chart is shown in the image below.if the resistance is above 2200 ohms at room temperature, then the sensor probe is causing the f10 error code and will need Sign In Register Save to this computer* This option is valuable if you expect to revisit Sears PartsDirect using this computer and browser in the future. *Saved models will only persist weblink Any suggestions on repair?

You will need a volt/ohm meter to check the resistance of this component. by Ken Williams 0 votes Didn't find what you are looking for? Please help! After the back panel is off remove the wired clip connector to the sensor and put your meter leads into the clip.

You should read close to the same resistance through the harness and sensor that you read though just the sensor.