Home > Kenmore Oven > Kenmore Oven Error F31

Kenmore Oven Error F31

MML // Mar 31, 2015 at 4:09 pm Hi Gene, Thanks so much for your reply. You may want to start the troubleshooting from testing the temperature probe (sensor). Valid for standard ground shipping within the continental United States and not valid for shipments to Alaska, Hawaii, Puerto Rico, Guam and the US Virgin Islands. Gene // May 12, 2015 at 10:39 pm Hello Michele, More likely the problem is a faulty EOC because the error code came up when the door lock was not used. this contact form

Sometimes while the oven is on but most of the time while the oven is cooling off. When I searched for a part it appears you can't just replace the ribbon connector, but have to replace the whole TST panel ($600!!). Parts Questions & Answers Questions & Answers about this model powered by Error message F31 for Kenmore Elite range I am getting the following error message on my Kenmore Elite gas Your question was published, help is on its way!

Do i have just 1 problem or 2 problems, i am not sure what i need to order. Offer valid for online purchases only. In order to provide most accurate advice I need the complete model number of the oven and the part number of the EOC you installed. https://www.dropbox.com/s/afvfo1xuvvrlsef/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%201.doc?dl=0 https://www.dropbox.com/s/uyrdx536z25aege/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%202.doc?dl=0 https://www.dropbox.com/s/ntcglkxlq82agdk/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%203.doc?dl=0 Keep me updated.

Ken // Dec 25, 2014 at 7:12 am Hello Gene, Thank you for GLEFS77CSC is the model number I was able to clear the lock and the oven gave an F1 If you replace the probe and still have a problem, then it is likely that the ERC control board will need to be replaced. If you need more specific help with this I was reading your site and trouble shooting. Could the oven control data be used to verify these failures, maybe downloaded by a tech ?

Frigidaire does not sell such harness but you can find a similar wires in a local electric or hardware store. Gene // Dec 26, 2014 at 2:29 pm Hello Rick, This problem can be caused by a faulty temperature sensor as well as a faulty relay board. I was out of town. Thank you for stopping by.

the "f31" fault code implies a shorted temperature sensor probe. note: disconnect the power cord from the range before removing the rear panels and checking the oven temperature sensor circuit.if you find a faulty sensor, the sensor #316217003 can be ordered Joey S, October 18, 2010 i understand your concern. I checked the resistance on the probe's bare wires and it reads 1099 ohms.

Gene. Thanks for your help Gene // Apr 23, 2015 at 10:12 pm Hello Jeff. code goes away immediately upon opening the oven door. If the oven will continue to heat, the oven relay board would need to replaced.

Please help! weblink This time the relay board will likely need to be replaced again but where last time the fault was visibly on the board, this time the burn was on the pins NOTE: Be careful. What is wrong with the oven temperature and what is the difference between the set and actual temperatures?

Examples: Try searching again: Model Number GO Can't find your model number? Any of these coils are not serviceable. Ask a question Get up to 30 % off On Wall Ovens Related Questions Related Questions'>Why is my Kenmore oven displaying an F31 error code? 1 answer Related Questions'>What does "F31" navigate here See Details More Products Kenmore 27" Electric Combination Wall Oven - ...

Internal metal edges in the range can be sharp. Gene // Sep 14, 2015 at 6:59 pm Hello Jack, Sorry for the delay. She hit oven cancel and it went off but then started beeping again and the same code appeared.

Previously, a new EOC had been installed (and the ignitor - elements had cracked).

The normal reading should be about 1100 Ohms at the room temperature. I placed my order for the needed EOC today. Keep me posted. Valerie // Dec 17, 2014 at 8:27 am Hello Gene!

The range is beeping with the error code F11. Frigidaire used the name RTD sensor or RTD probe, where RTD means "Resistance Temperature Detector" instead of oven temperature sensor. Jacqui // Jan 3, 2015 at 3:06 am Ok so with your website I've figured out what is wrong with my stove…it won't stop beeping and my problem is won't be his comment is here Thanks again.

It would need to be replaced. Gene. It was 1 hr into baking and the temperature did runaway, everything was black. Appreciate any help!

I have a Frigidaire Mod. #FGF337ABJ It's throwing the F10. Keep me posted. FGGF3076KBK. The oven was working fine until in the last couple of days the PF code would come on after the oven had been on for a while.

Gene. Well, it was almost a year to the date. A wiring failure could also cause this problem. NOTE : You should only access and check internal range components if you are completely confident in your technical ability to safely perform Sorry for the delay.

You can not check the EOC instrumentally. F3 or F30 - Open/shorted sensor (RTD probe) connection. Gene // Dec 24, 2014 at 5:31 pm Hi Ken, Merry Christmas and Happy New year to you as well! George sharon // Jan 1, 2015 at 10:09 pm i have a frigidaire model fgef301dnb.

Model retention may be affected by your browser settings. See Details Related Pages Kenmore 5M followers Follow Appliances 161K followers Follow Wall Ovens 187 followers Follow Sweeps Personal Shopper Gift Registry Legal & Privacy | Help | Feedback Skip to Get help locating it Request unsuccessful.